Tel: +8613666033393 E-mail: [email protected]

About | Contact

Two Ports, One Loop Too Many: Network Storms Caused by the Honeywell 10014/1/1

Blog Excellent PLC

Home

Blog Excellent PLC

Two Ports, One Loop Too Many: Network Storms Caused by the Honeywell 10014/1/1

2026-02-02 Troubleshooting

By Nathan Brooks – Control Network Engineer Dual-port modules are meant to increase resilience. Used correctly, the Honeywell 10014/1/1 dual-port module provides flexible routing and redund……

Read more
Why the Honeywell 10012/1/2 Always Fails at the Worst Possible Time

2026-01-30 Troubleshooting

By Michael O’Connor – Automation Asset Manager From an asset management point of view, the Honeywell 10012/1/2 CPU module is one of the most deceptive components in a control system. ……

Read more
Designed for Stability, Not Constant Change: The Honeywell 10012/1/2 Flash Problem Nobody Talks About

2026-01-30 Troubleshooting

By Richard Hammond – Independent Control Systems Consultant The Honeywell 10012/1/2 CPU module was designed in an era when control systems were meant to be finished, not continuously edited……

Read more
02:43 AM and Something Was Off: Night Shift Notes on a Honeywell 10012/1/2 CPU

2026-01-30 Troubleshooting

By Kevin Moore – Shift Control Engineer Night shifts teach you to trust patterns. That’s why this one bothered me. 02:43 – The System Was “Running” No alarms.No wat……

Read more
A Firmware Upgrade That Should Have Waited: Lessons from Honeywell 10012/1/2 Flash Corruption

2026-01-30 Troubleshooting

By Thomas Reed – Lead Automation Integrator Firmware upgrades are supposed to be routine. On paper, updating the Honeywell 10012/1/2 CPU module looked straightforward: same hardware, minor ……

Read more
The Controller That Never Started: Boot-Stage Flash Check Failure in Honeywell 10012/1/2

2026-01-30 Troubleshooting

Incident summary prepared by Laura McKenzie – Control Systems Reliability Team Incident Overview At 02:17 local time, a scheduled power restoration was completed following planned electrica……

Read more
When Memory Forgets: Flash Degradation in the Honeywell 10012/1/2 CPU Module

2026-01-30 Troubleshooting

By Andrew Collins – Senior DCS Systems Engineer Most CPU failures don’t start with smoke or alarms. They start with memory. The Honeywell 10012/1/2 CPU module, like many controller CP……

Read more
Nothing Was Broken — Until We Took Over: Honeywell 10008/2/U in a Poorly Handed-Over System

2026-01-30 Troubleshooting

By Daniel Ruiz – Maintenance Lead, Process Automation When we officially took over the system, everyone said the same thing: “Everything is running fine.” That should have worri……

Read more
A Week Spent Chasing Ghosts: Notes from a Honeywell 10008/2/U Troubleshooting Log

2026-01-30 Troubleshooting

Field notes by Mark Jensen – Commissioning Engineer I didn’t think the communication module was the problem at first. The Honeywell 10008/2/U had been running in this system for years……

Read more
Redundancy That Reduces Reliability: A Hard Lesson from Honeywell 10008/2/U

2026-01-30 Troubleshooting

By Eleanor Watkins – Control System Design Auditor Redundancy is supposed to make systems safer.But when it is misunderstood, it does the opposite. This became painfully clear during a syst……

Read more
When Expansion Breaks Communication: A Honeywell 10008/2/U Case Study

2026-01-30 Troubleshooting

By Steven Patel – Control System Architecture Consultant Communication modules usually fail for obvious reasons: power loss, wiring damage, configuration errors.The Honeywell 10008/2/U comm……

Read more
After the Surge, Nothing Failed — Except the Margins

2026-01-29 Troubleshooting

By Robert Sinclair – Industrial Electronics Reliability Engineer The most expensive failures are not the ones that break equipment.They are the ones that quietly erode safety margins. This ……

Read more

<<<···64 656667 68 ··· >

[email protected]

Leave a message